PETIKEMAS offers competitive rates for 20’ ISO TANK CONTAINER short-term or long-term rental.
Contact us for more information
+6680 539-3883
[email protected]
Other services include
26,000L-20′ ISO TANK CONTAINER Specification |
|
| CAPACITY | 26,000 Litres |
| Frame (L/W/H) | 6058/2438/2591mm |
| TARE MASS | 3,800 kg |
| MAX GROSS MASS | 36,000 kg |
| PRODUCTS | General purpose liquids |
| HYDROSTATIC TEST PRESSURE | 6 bar |
| VESSEL DESIGN TEMP | -40℃ to 130℃ |
| TEMPERATURE (@atm P) | 140℃ |
| DESIGN CODE | ASME Ⅷ DIV. 1 |
| TYPE APPROVALS | UN portable tank (T11 IMDG, CFR49, ADR/RID), UIC, TIR, CSC, TC, ADR L4BN |
| CLASSIFICATION | Bureau Veritas |
| STACKING TEST | Each container is approved for 9 high stacking at 24,000kg |
| SAFETY RELIEF ASSEMBLY | 2½” BSP safety relief valve without gauze. Pressure only model set at +4.4 bar (63.8psi), complete with Adaptor and gauge guard |
| MANHOLE | 500mm low profile, 8 point fixing. The manlid is completedwith TIR |
| AIR INLET ASSEMBLY | DN 40 ball valve terminating with 1½” BSP connection and cap |
| TOP DISCHARGE PROVISION | DN80 stainless steel 316 tank pad with not less than 94mm hole with blind flange. The assembly is fitted off centre on a low profile horizontal tank pad. Flange to be dual drilled: 6×M12 on 168.3PCD and 4×M16 on 160PCD |
| BOTTOM DISCHARGE | FV: DN80 30° Univalve footvalve terminating with a 3″ BSP spigot with cap and chain. Perolo: DN80 30° TWINCO footvalve terminating with a 3″ BSP spigot with cap and chain. The bottom flange is a normal flange. |
| STEAM HEATING | 8 runs steam heating system. Longitudinal steam channels manufactured from Duplex stainless steel. Heating provided to BDC area. Actual heating area 4.57 m2, effective heating area 9.6m2. |
| PRESSURES | 4 bar working pressure |
| CONNECTIONS | 1″ BSP inlet, 1″ BSP outlet. Stainless steel dustcaps fitted. |
| INSULATION | 50mm Rockwool where possible. |
Extract from Table IMDG 4.2.5.2.6 – Portable tank instructions
| Portable tank instruction | Minimum shell thickness (reference steel) | Minimun test pressure (bar) | Bottom opening requirement |
| T1 | See 6.7.2.4.2 | 1.5 | 2 closures |
| T2 | See 6.7.2.4.2 | 1.5 | 3 closures |
| T3 | See 6.7.2.4.2 | 2.65 | 2 closures |
| T4 | See 6.7.2.4.2 | 2.65 | 3 closures |
| T5 | See 6.7.2.4.2 | 2.65 | Prohibited |
| T6 | See 6.7.2.4.2 | 4 | 2 closures |
| T7 | See 6.7.2.4.2 | 4 | 3 closures |
| T8 | See 6.7.2.4.2 | 4 | Prohibited |
| T9 | 6mm | 4 | Prohibited |
| T10 | 6mm | 4 | Prohibited |
| T11 | See 6.7.2.4.2 | 6 | 3 closures |
| T12 | See 6.7.2.4.2 | 6 | 3 closures |
| T13 | 6mm | 6 | Prohibited |
| T14 | 6mm | 6 | Prohibited |
| T15 | See 6.7.2.4.2 | 10 | 3 closures |
| T16 | See 6.7.2.4.2 | 10 | 3 closures |
| T17 | 6mm | 10 | 3 closures |
| T18 | 6mm | 10 | 3 closures |
| T19 | 6mm | 10 | Prohibited |
| T20 | 8mm | 10 | Prohibited |
| T21 | 10mm | 10 | Prohibited |
| T22 | 10mm | 10 | Prohibited |
